Sony Flat Panel Television SPMTRI C User Manual

®
INSTALLATION MANUAL  
Sony Electronics Inc.  
16450 West Bernardo Drive  
San Diego, CA 92127  
 
Stand diagrams  
PART#:  
SPMTRI/C  
MATERIALS USED:  
12 (GA) CRS, Clear acrylic base  
COLOR:  
Silver  
A. Back plate  
B. Stand support  
C. Clear base  
D. Security access screws  
E. (1) Cable access hole  
F. Fixed tabletop mounting holes  
Dimensions are in Inch and mm  
18.25  
(463.5)  
20.50  
(520.7)  
20.00  
(508)  
1.00  
(25.4)  
12 X 22  
(304 x 558)  
(A)  
MODEL  
A
PFM-32C1  
.37 (9.4)  
1.0 (25.4)  
.72 (18.2)  
1.0 (25.4)  
.90 (22.8)  
1.0 (25.4)  
FWD32LX1,FWD32DV1  
PFM-42B1,PFM-42V1, FWD42X1  
PFM-42LX1, FWD42DV1  
PFM-50C1  
PFM-50DV1  
- 3 -  
 
Parts List  
TOOLS & SUPPLY NEEDED  
HARDWARE  
Phillips screwdriver  
(4) M5 x 10 (mm) flat head Phillip screws (4) Clear rubber feet  
(6) M5 x 30 (mm) flat head Phillip screws (2) M6 x 30 Phillips head screws (used on the 30” plasma only)  
(2) M5 x 12 (mm) phillip security screws (used on 42" and 50" plasma displays only)  
(2) #10 x 1-3/4" wood screws (Optional use)  
Building the stand  
Step 1  
Unpack the components from the box and set them on the floor. Invert and apply the four (4) clear rubber feet to the flat surface on the  
base, locate the four mounting points on the clear base. Secure the two (2) upright supports (flat surface facing out) to the base by using  
the four (6) M5 x 30 (mm) Phillip screws (supplied). CAUTION: Do not over tighten the screws.  
Uprights  
Clear base  
(6) M5 x 30  
Flat head screws  
Step 2  
The stand fits a 32" 42" and 50" PFM series (Sony plasma displays only). The plate is stamped with two plasma sizes. Check the size that  
fits your plasma before installing. NOTE: If using a 32” plasma, the plate is not needed. Mount the plasma quick release sleeves from  
the plasma to the key-holes on the uprights.  
The size and arrow must always point up prior to installation, finger tighten the (4) M5 x 10 (mm) phillips flat head screws then tighten the  
screws. See figure 2.  
50"  
42"  
(4) M5 x 10  
Flat head screws  
Mounting plate  
- 4 -  
 
Securing the plasma to the stand  
Step 3  
Raise the display with the securing sleeves installed to the plasma. Slip the sleeves through the four (4) keyholes on the back plate and  
drop it down slowly, make sure all of the four (4) sleeves are in the keyhole slot before letting go of the plasma. On the 42" and 50" two (2)  
M5 x 12 Phillip screws (security screws) can be used for additional security. See figure 3.  
NOTE: If using a 32” plasma, secure it with the two (2) M6 x 30 Phillip screws supplied.  
NOTE: Two (2) security screws for  
the 42" and 50" plasma displays.  
Check all hardware for proper  
tightness and security.  
M5 x 12 phillips  
screws  
NOTE: Security screws for the 32”  
plasma displays. Check all hardware  
for proper tightness and security.  
M6 x 30 phillips  
screws  
- 5 -  
 
(Optional) fixed installation  
Step 1  
Invert the stand and locate the two (2) mounting points on the bottom of the stand for (optional) fixed tabletop installation. Measure the  
distance between center to center of these two (2) holes and mark the table. See figure 4.  
NOTE: This diagram shows  
the bottom of the stand.  
Wood screw  
access holes  
Step 2  
OPTIONAL TABLE MOUNTING  
If securing to a wood table, mark the table and drill properly. Secure the stand with the two (2) #10 x 1-1/4" wood screws (supplied).  
NOTE: Longer or shorter wood screws and or mounting hardware depending on your installation environment are (commercially  
available). See figure 5.  
#10x1-1/4”  
woodscrews  
Flat wood surface  
NOTE: Check all hardware for proper  
tightness and security.  
- 6 -  
 

Sharp Blower AIR BLOWER User Manual
Sharp Computer Monitor DK A1 User Manual
Sharp CRT Television SX68NF8 User Manual
Shure Microphone wl183 User Manual
Singer Sewing Machine 114W100 User Manual
Sony CD Player CDX 848X User Manual
Southbend Fondue Maker P32 CM User Manual
Spin Master Motorized Toy Car Triple Booster User Manual
Sunbeam Food Processor LC7600 User Manual
Sylvania DVD Player DVL700D User Manual